Weblink Items (0)
Bubbles of common problems in injection molding
According to the causes of bubbles, the solutions are as follows:
1) When the wall thickness of the product is large, the cooling speed of the outer surface is faster than that of the center part. Therefore, with the cooling process, the resin in the center part shrinks and expands to the surface, resulting in insufficient filling in the center part. custom plastic injection molding service china This is called a vacuum bubble. The solutions are as follows:
a) According to the wall thickness, determine the reasonable gate and sprue size. Generally, the gate height shall be 50% – 60% of the wall thickness of the product.
b) Until the gate is sealed, a certain amount of supplementary injection material is reserved.
C) The injection time should be a little longer than the gate sealing time.
d) Reduce injection speed and increase injection pressure,
e) Adopt the material with high melting viscosity grade.
Coupon code: free shipping on any order over 2000USD from https://www.jasonmolding.com/plastic-injection-molding/
2) The solutions to the bubbles caused by the generation of volatile gases are as follows:
a) Sufficient pre drying.
b) Reduce the temperature of resin to avoid decomposition gas.
3) The bubbles caused by poor fluidity can be solved by increasing the temperature of resin and mould and the injection speed.
About JasonMould Industrial Company Limited
Jasonmould is a China mold maker of plastic molds- injection mold, die casting moulds, plastic blow molding, rotational molding, medical plastic injection molding, two shot plastic injection molding, insert molding, overmolding, metal injection molding, micro injection molding, powder injection molding, ceramic injection molding, liquid injection molding, husky injection molding, household mold, casting mold, die mold tool, custom molds, china moulds, rapid prototyping tooling, plastic prototyping tooling, punch press tooling, die and tooling for mobile/ cell phone parts, automotive parts, vacuum cleaners, rechargeable tools, telephones, copiers, computers, multimedia speakers, and many other electronic products and household appliances. And also a plastic product manufacturer, mold manufacturer China– plastic parts, plastic water tank, plastic balls, plastic containers, plastic buckle, plastic anchor, plastic hanger, plastic spoon, plastic pipe fitting, plastic tumble, plastic tableware, plastic cups, plastic bottles, plastic tray, plastic cosmetic container, plastic case, plastic food container, plastic chairs, plastic caps, plastic cap closure, plastic tubes, plastic water pipes, plastic knobs, plastic tubing, plastic utility boxes, plastic racks and so on.
Contact:
Person: James Yuan
Company: JasonMould Industrial Company Limited
Add: LongGang Village,LongXi Town,BoLuo County,HuiZhou City,GuangDong Province, China
Tel: 86-752-6682869
Email: james@jasonmolding.com
Site: https://www.jasonmolding.com/custom-injection-molding/
What will be caused when injection mold testing in many times?
The design of the injection mold was not fully collectively reviewed, and the structure of the injection mold was unreasonable, which caused the injection mold to undergo multiple improvements after the test, which made the injection mold cost exceed the budget.
If it can be solved after several improvements, it is relatively fortunate. There are many cases that are unsatisfactory, and even the injection molds have to be scrapped and reworked. This cost cannot be controlled.
There are also cases where the design of the injection mold is good, but the processing of the injection mold is not in place, which makes the number of trial molds increase unreasonably, directly increasing the cost of the injection mold.
There is no objection to this problem, so many injection mold manufacturers have increased their investment in measuring equipment.
The best molding process and model of the injection molding machine were not selected during the mold test. Obviously, the injection mold is good enough but the molded parts was not ideal.
There is not enough understanding of the material data of plastic, and even the shrinkage rate is no accurate. This happens from time to time. Therefore, before designing the injection mold, it is necessary to understand the material data of the plastic to effectively reduce the mold trial.
coupon code: freeshipping on any order over 2000USD from jasonmolding.com
JasonMould Industrial Company Limited is a plastic injection mold manufacturer specializing in one-stop service for injection mold making, parts production, spraying paint and assembly. The injection mold uses only internationally renowned brand raw materials, and strictly controls all tolerance from size to appearance and environmental protection. Using rich
FUTABA, LMK and other well-known mold base brands in the industry and Sweden’s ASSBA, Japan’s Daido, domestic Fushun steel and other well-known steel brands to ensure the life of injection molds up to 1 million times; use of Bayer, SABIC plastic materials. And the new material does not contain any recycled material, with full set of SGS, ROHS test reports, for more reliable use.
About JasonMould Industrial Company Limited
Low volume Manufacturing China
Jasonmould is a China mold maker of plastic molds- injection mold, die casting moulds, plastic blow molding, rotational molding, medical plastic injection molding, two shot plastic injection molding, insert molding, overmolding, metal injection molding, micro injection molding, powder injection molding, ceramic injection molding, liquid injection molding, husky injection molding, household mold, casting mold, die mold tool, custom molds, china moulds, rapid prototyping tooling, plastic prototyping tooling, punch press tooling, die and tooling for mobile/ cell phone parts, automotive parts, vacuum cleaners, rechargeable tools, telephones, copiers, computers, multimedia speakers, and many other electronic products and household appliances. And also a plastic product manufacturer, mold manufacturer China– plastic parts, plastic water tank, plastic balls, plastic containers, plastic buckle, plastic anchor, plastic hanger, plastic spoon, plastic pipe fitting, plastic tumble, plastic tableware, plastic cups, plastic bottles, plastic tray, plastic cosmetic container, plastic case, plastic food container, plastic chairs, plastic caps, plastic cap closure, plastic tubes, plastic water pipes, plastic knobs, plastic tubing, plastic utility boxes, plastic racks and so on.
Contact:
Person: James Yuan
Company: JasonMould Industrial Company Limited
Add: LongGang Village,LongXi Town,BoLuo County,HuiZhou City,GuangDong Province, China
Tel: 86-752-6682869
Email: james@jasonmolding.com
Site: https://www.jasonmolding.com/custom-injection-molding/
What will be caused when injection mold testing in many times?
The design of the injection mold was not fully collectively reviewed, and the structure of the injection mold was unreasonable, which caused the injection mold to undergo multiple improvements after the test, which made the injection mold cost exceed the budget.
If it can be solved after several improvements, it is relatively fortunate. There are many cases that are unsatisfactory, and even the injection molds have to be scrapped and reworked. This cost cannot be controlled.
There are also cases where the design of the injection mold is good, but the processing of the injection mold is not in place, which makes the number of trial molds increase unreasonably, directly increasing the cost of the injection mold.
There is no objection to this problem, so many injection mold manufacturers have increased their investment in measuring equipment.
The best molding process and model of the injection molding machine were not selected during the mold test. Obviously, the injection mold is good enough but the molded parts was not ideal.
There is not enough understanding of the material data of plastic, and even the shrinkage rate is no accurate. This happens from time to time. Therefore, before designing the injection mold, it is necessary to understand the material data of the plastic to effectively reduce the mold trial.
coupon code: freeshipping on any order over 2000USD from jasonmolding.com
JasonMould Industrial Company Limited is a plastic injection mold manufacturer specializing in one-stop service for injection mold making, parts production, spraying paint and assembly. The injection mold uses only internationally renowned brand raw materials, and strictly controls all tolerance from size to appearance and environmental protection. Using rich
FUTABA, LMK and other well-known mold base brands in the industry and Sweden’s ASSBA, Japan’s Daido, domestic Fushun steel and other well-known steel brands to ensure the life of injection molds up to 1 million times; use of Bayer, SABIC plastic materials. And the new material does not contain any recycled material, with full set of SGS, ROHS test reports, for more reliable use.
About JasonMould Industrial Company Limited
Low volume Manufacturing China
Jasonmould is a China mold maker of plastic molds- injection mold, die casting moulds, plastic blow molding, rotational molding, medical plastic injection molding, two shot plastic injection molding, insert molding, overmolding, metal injection molding, micro injection molding, powder injection molding, ceramic injection molding, liquid injection molding, husky injection molding, household mold, casting mold, die mold tool, custom molds, china moulds, rapid prototyping tooling, plastic prototyping tooling, punch press tooling, die and tooling for mobile/ cell phone parts, automotive parts, vacuum cleaners, rechargeable tools, telephones, copiers, computers, multimedia speakers, and many other electronic products and household appliances. And also a plastic product manufacturer, mold manufacturer China– plastic parts, plastic water tank, plastic balls, plastic containers, plastic buckle, plastic anchor, plastic hanger, plastic spoon, plastic pipe fitting, plastic tumble, plastic tableware, plastic cups, plastic bottles, plastic tray, plastic cosmetic container, plastic case, plastic food container, plastic chairs, plastic caps, plastic cap closure, plastic tubes, plastic water pipes, plastic knobs, plastic tubing, plastic utility boxes, plastic racks and so on.
Contact:
Person: James Yuan
Company: JasonMould Industrial Company Limited
Add: LongGang Village,LongXi Town,BoLuo County,HuiZhou City,GuangDong Province, China
Tel: 86-752-6682869
Email: james@jasonmolding.com
Site: https://www.jasonmolding.com/custom-injection-molding/
What will be caused when injection mold testing in many times?
The design of the injection mold was not fully collectively reviewed, and the structure of the injection mold was unreasonable, which caused the injection mold to undergo multiple improvements after the test, which made the injection mold cost exceed the budget.
If it can be solved after several improvements, it is relatively fortunate. There are many cases that are unsatisfactory, and even the injection molds have to be scrapped and reworked. This cost cannot be controlled.
There are also cases where the design of the injection mold is good, but the processing of the injection mold is not in place, which makes the number of trial molds increase unreasonably, directly increasing the cost of the injection mold.
There is no objection to this problem, so many injection mold manufacturers have increased their investment in measuring equipment.
The best molding process and model of the injection molding machine were not selected during the mold test. Obviously, the injection mold is good enough but the molded parts was not ideal.
There is not enough understanding of the material data of plastic, and even the shrinkage rate is no accurate. This happens from time to time. Therefore, before designing the injection mold, it is necessary to understand the material data of the plastic to effectively reduce the mold trial.
coupon code: freeshipping on any order over 2000USD from jasonmolding.com
JasonMould Industrial Company Limited is a plastic injection mold manufacturer specializing in one-stop service for injection mold making, parts production, spraying paint and assembly. The injection mold uses only internationally renowned brand raw materials, and strictly controls all tolerance from size to appearance and environmental protection. Using rich
FUTABA, LMK and other well-known mold base brands in the industry and Sweden’s ASSBA, Japan’s Daido, domestic Fushun steel and other well-known steel brands to ensure the life of injection molds up to 1 million times; use of Bayer, SABIC plastic materials. And the new material does not contain any recycled material, with full set of SGS, ROHS test reports, for more reliable use.
About JasonMould Industrial Company Limited
Low volume Manufacturing China
Jasonmould is a China mold maker of plastic molds- injection mold, die casting moulds, plastic blow molding, rotational molding, medical plastic injection molding, two shot plastic injection molding, insert molding, overmolding, metal injection molding, micro injection molding, powder injection molding, ceramic injection molding, liquid injection molding, husky injection molding, household mold, casting mold, die mold tool, custom molds, china moulds, rapid prototyping tooling, plastic prototyping tooling, punch press tooling, die and tooling for mobile/ cell phone parts, automotive parts, vacuum cleaners, rechargeable tools, telephones, copiers, computers, multimedia speakers, and many other electronic products and household appliances. And also a plastic product manufacturer, mold manufacturer China– plastic parts, plastic water tank, plastic balls, plastic containers, plastic buckle, plastic anchor, plastic hanger, plastic spoon, plastic pipe fitting, plastic tumble, plastic tableware, plastic cups, plastic bottles, plastic tray, plastic cosmetic container, plastic case, plastic food container, plastic chairs, plastic caps, plastic cap closure, plastic tubes, plastic water pipes, plastic knobs, plastic tubing, plastic utility boxes, plastic racks and so on.
Contact:
Person: James Yuan
Company: JasonMould Industrial Company Limited
Add: LongGang Village,LongXi Town,BoLuo County,HuiZhou City,GuangDong Province, China
Tel: 86-752-6682869
Email: james@jasonmolding.com
Site: https://www.jasonmolding.com/custom-injection-molding/
What will be caused when injection mold testing in many times?
The design of the injection mold was not fully collectively reviewed, and the structure of the injection mold was unreasonable, which caused the injection mold to undergo multiple improvements after the test, which made the injection mold cost exceed the budget.
If it can be solved after several improvements, it is relatively fortunate. There are many cases that are unsatisfactory, and even the injection molds have to be scrapped and reworked. This cost cannot be controlled.
There are also cases where the design of the injection mold is good, but the processing of the injection mold is not in place, which makes the number of trial molds increase unreasonably, directly increasing the cost of the injection mold.
There is no objection to this problem, so many injection mold manufacturers have increased their investment in measuring equipment.
The best molding process and model of the injection molding machine were not selected during the mold test. Obviously, the injection mold is good enough but the molded parts was not ideal.
There is not enough understanding of the material data of plastic, and even the shrinkage rate is no accurate. This happens from time to time. Therefore, before designing the injection mold, it is necessary to understand the material data of the plastic to effectively reduce the mold trial.
coupon code: freeshipping on any order over 2000USD from jasonmolding.com
JasonMould Industrial Company Limited is a plastic injection mold manufacturer specializing in one-stop service for injection mold making, parts production, spraying paint and assembly. The injection mold uses only internationally renowned brand raw materials, and strictly controls all tolerance from size to appearance and environmental protection. Using rich
FUTABA, LMK and other well-known mold base brands in the industry and Sweden’s ASSBA, Japan’s Daido, domestic Fushun steel and other well-known steel brands to ensure the life of injection molds up to 1 million times; use of Bayer, SABIC plastic materials. And the new material does not contain any recycled material, with full set of SGS, ROHS test reports, for more reliable use.
About JasonMould Industrial Company Limited
Low volume Manufacturing China
Jasonmould is a China mold maker of plastic molds- injection mold, die casting moulds, plastic blow molding, rotational molding, medical plastic injection molding, two shot plastic injection molding, insert molding, overmolding, metal injection molding, micro injection molding, powder injection molding, ceramic injection molding, liquid injection molding, husky injection molding, household mold, casting mold, die mold tool, custom molds, china moulds, rapid prototyping tooling, plastic prototyping tooling, punch press tooling, die and tooling for mobile/ cell phone parts, automotive parts, vacuum cleaners, rechargeable tools, telephones, copiers, computers, multimedia speakers, and many other electronic products and household appliances. And also a plastic product manufacturer, mold manufacturer China– plastic parts, plastic water tank, plastic balls, plastic containers, plastic buckle, plastic anchor, plastic hanger, plastic spoon, plastic pipe fitting, plastic tumble, plastic tableware, plastic cups, plastic bottles, plastic tray, plastic cosmetic container, plastic case, plastic food container, plastic chairs, plastic caps, plastic cap closure, plastic tubes, plastic water pipes, plastic knobs, plastic tubing, plastic utility boxes, plastic racks and so on.
Contact:
Person: James Yuan
Company: JasonMould Industrial Company Limited
Add: LongGang Village,LongXi Town,BoLuo County,HuiZhou City,GuangDong Province, China
Tel: 86-752-6682869
Email: james@jasonmolding.com
Site: https://www.jasonmolding.com/custom-injection-molding/
The design of the injection mold was not fully collectively reviewed, and the structure of the injection mold was unreasonable, which caused the injection mold to undergo multiple improvements after the test, which made the injection mold cost exceed the budget.
If it can be solved after several improvements, it is relatively fortunate. There are many cases that are unsatisfactory, and even the injection molds have to be scrapped and reworked. This cost cannot be controlled.
There are also cases where the design of the injection mold is good, but the processing of the injection mold is not in place, which makes the number of trial molds increase unreasonably, directly increasing the cost of the injection mold.
There is no objection to this problem, so many injection mold manufacturers have increased their investment in measuring equipment.
The best molding process and model of the injection molding machine were not selected during the mold test. Obviously, the injection mold is good enough but the molded parts was not ideal.
There is not enough understanding of the material data of plastic, and even the shrinkage rate is no accurate. This happens from time to time. Therefore, before designing the injection mold, it is necessary to understand the material data of the plastic to effectively reduce the mold trial.
coupon code: freeshipping on any order over 2000USD from jasonmolding.com
JasonMould Industrial Company Limited is a plastic injection mold manufacturer specializing in one-stop service for injection mold making, parts production, spraying paint and assembly. The injection mold uses only internationally renowned brand raw materials, and strictly controls all tolerance from size to appearance and environmental protection. Using rich
FUTABA, LMK and other well-known mold base brands in the industry and Sweden’s ASSBA, Japan’s Daido, domestic Fushun steel and other well-known steel brands to ensure the life of injection molds up to 1 million times; use of Bayer, SABIC plastic materials. And the new material does not contain any recycled material, with full set of SGS, ROHS test reports, for more reliable use.
About JasonMould Industrial Company Limited
Low volume Manufacturing China
Jasonmould is a China mold maker of plastic molds- injection mold, die casting moulds, plastic blow molding, rotational molding, medical plastic injection molding, two shot plastic injection molding, insert molding, overmolding, metal injection molding, micro injection molding, powder injection molding, ceramic injection molding, liquid injection molding, husky injection molding, household mold, casting mold, die mold tool, custom molds, china moulds, rapid prototyping tooling, plastic prototyping tooling, punch press tooling, die and tooling for mobile/ cell phone parts, automotive parts, vacuum cleaners, rechargeable tools, telephones, copiers, computers, multimedia speakers, and many other electronic products and household appliances. And also a plastic product manufacturer, mold manufacturer China– plastic parts, plastic water tank, plastic balls, plastic containers, plastic buckle, plastic anchor, plastic hanger, plastic spoon, plastic pipe fitting, plastic tumble, plastic tableware, plastic cups, plastic bottles, plastic tray, plastic cosmetic container, plastic case, plastic food container, plastic chairs, plastic caps, plastic cap closure, plastic tubes, plastic water pipes, plastic knobs, plastic tubing, plastic utility boxes, plastic racks and so on.
Contact:
Person: James Yuan
Company: JasonMould Industrial Company Limited
Add: LongGang Village,LongXi Town,BoLuo County,HuiZhou City,GuangDong Province, China
Tel: 86-752-6682869
Email: james@jasonmolding.com
Site: https://www.jasonmolding.com/custom-injection-molding/
Is Startprototyping’s rapid prototyping service one of the fastest on the market?
The manufacturers worldwide have dedicated themselves to transform all their processes to be at the forefront, as well as the designs of all their customers, since within their main functions is to make all the designs and ideas that need to manufacture their customers, this has generated as a result that all companies dedicated to the manufacture of products have to modify certain techniques to be at the forefront and evolve along with the designs that are requested.
Shenzhen rapid prototyping
Many manufacturers are not yet familiar with certain production processes.
Currently, it is a requirement that all manufacturers know how to operate under one of the modern production processes, not because some rule dictates so, but because of the influence of their clients, who left the designs impractical in the past.
Startprototyping is an excellent company that has successfully integrated multiple processes.
If someone requires multiple services that involve the most innovative and varied modern processes for the manufacture of parts, you can draw on the attention Startprototyping provides for the public.
Startprototyping has all the features that an excellent manufacturer needs; Apart from an excellent working methodology, strict safety rules and a team dedicated to perfecting all its tasks, it also has the enormous advantage of knowing in detail the most current and requested manufacturing processes, for example the additive manufacturing.
Of all the products that this factory offers is the rapid prototyping service that consists in the realization of a piece under the indications of design, they are usually orders of a quantity very inferior to the one that they request in other services, this due to the complexity of the piece, since most of these additive manufacturing services are requested for testing or prototype release.
A rapid prototyping service can be performed for an incredibly short time, without having to sacrifice even a little quality to be able to complete all the parts that have been ordered from the manufacturer.
coupon code: freeshipping on any order over 5000USD from startprototyping.com
Why is Startprototyping the fastest manufacturer?
Usually, for many companies, the delivery time of these products can vary, it takes approximately 15 or 20 days to complete all the pieces, then move them to their destinations, then this would be another extra time that must elapse before it can reach the hands of the clients.
In Startprototyping has become accustomed to make the products in a fairly fast and practical and these are of excellent quality, the additive manufacturing is one of the strengths of the company, which is why they have become accustomed to create pieces under this procedure in a short 7 days minimum and maximum 10 days, and this including the days of packaging and transfer, so it is an unparalleledly fast service.
No other company is capable of manufacturing in detail and satisfactorily everything proposed in a rapid prototyping service, however Startprototyping has already made it clear that it is capable of this and much more, since all its services are focused on quality and the fastest response time.
For more about rapid prototyping service in china,you can pay a visit to https://www.startprototyping.com/
About Start Prototyping
Start Prototyping mainly supply our rapid prototyping service and plastic injection manufacturing for many 3D print companies in the world.
Start Prototyping has been engaged in rapid prototyping about 10 years, helping too many designers to turn their ideas into reality. Most of the conceptual prototype of the design has been successfully put into the market and has achieved good benefits. Among them, the most representative metal prototype machining, plastic prototype machining, CNC aluminum machining, Low-Volume Manufacturing, processing technology including CNC machining, vacuum casting, rapid tooling, 3D printing and so on. We have the standard quality inspection process, which is completely in line with the customer’s industrial design. It’s a great honor to be a partner with you.
Contact Info
Contact:James Yuan
Company:Start Prototyping
Add:LongGang Village, LongXi Town, BoLuo County, HuiZhou City,GuangDong Province, China
Tel:+86-13352636504
Email:info@startprototyping.com
Web:https://www.startprototyping.com
Why do injection moulds need to be tested
Defects in most injection molding products are caused during the plasticizing and injection phases of the injection molding parts, but are sometimes related to design irrationality, including the type of injection port, the number of mold cavities, location and size, the design of the cold and hot runner system, and the structure of the product itself. Therefore, in order to avoid product defects caused by mold design, we need to analyze the injection mold during production.
After the test results of injection mold are obtained, the operator usually needs to evaluate the specific conditions of the mold, so as not to increase unnecessary costs and time in the process of modification. low volume manufacturing service In most cases, in order to make up for its deficiency in die design, the operator may be unwittingly made incorrect Settings, because the parameters required for the production of qualified products range is very small, once there’s any deviation in parameter Settings, may lead to the final product quality far beyond the allowed error range.
freeshipping on any order over 2000USD from jasonmolding.com
The purpose of the injection mold test is to find out the optimized process parameters and mold design. Not just to get a good sample. This is very important. Even if materials, machine Settings or environmental factors change, it can still ensure a stable and continuous mass production environment.
About JasonMould Industrial Company Limited
Rapid Prototyping Service
Jasonmould is a China mold maker of plastic molds- injection mold, die casting moulds, plastic blow molding, rotational molding, medical plastic injection molding, two shot plastic injection molding, insert molding, overmolding, metal injection molding, micro injection molding, powder injection molding, ceramic injection molding, liquid injection molding, husky injection molding, household mold, casting mold, die mold tool, custom molds, china moulds, rapid prototyping tooling, plastic prototyping tooling, punch press tooling, die and tooling for mobile/ cell phone parts, automotive parts, vacuum cleaners, rechargeable tools, telephones, copiers, computers, multimedia speakers, and many other electronic products and household appliances. And also a plastic product manufacturer, mold manufacturer China– plastic parts, plastic water tank, plastic balls, plastic containers, plastic buckle, plastic anchor, plastic hanger, plastic spoon, plastic pipe fitting, plastic tumble, plastic tableware, plastic cups, plastic bottles, plastic tray, plastic cosmetic container, plastic case, plastic food container, plastic chairs, plastic caps, plastic cap closure, plastic tubes, plastic water pipes, plastic knobs, plastic tubing, plastic utility boxes, plastic racks and so on.
Contact:
Person: James Yuan
Company: JasonMould Industrial Company Limited
Add: LongGang Village,LongXi Town,BoLuo County,HuiZhou City,GuangDong Province, China
Tel: 86-752-6682869
Email: james@jasonmolding.com
Site: https://www.jasonmolding.com/custom-injection-molding/
Key points of boss design
Screw post is also called boss, which is a feature of most products. What key points should we pay attention to when designing the structure? Let’s have a look:
The wall thickness of the boss, at the time of structure design, we need to consider the strength of the boss, so as far as possible the post do thick wall thickness, but this will lead to positive forming parts shrink, we can design according to the main body of the wall thickness of boss wall thickness, generally not less than 0.8 mm, can only do in mold department is greater than 0.8 mm tube, for their depth of more than 15 mm parts we must pay attention to this; It cannot be more than 60% of the wall thickness of the main body, which is our accumulated experience in thousands of sets of molds. If the surface of the part cannot accept shrinkage, you are better to accept our experience.
Reduce the wall thickness of the boss, strength weakened will follow, probably can’t meet our functional requirements, such as torsion test tensile test and so on, china mold maker this is can be improved by increasing the stiffener, namely we often say that rib, it will make the strength of pillars is better than the original wall thickness of the pillar strength, and perfectly to avoid sink mark.
freeshipping on any order over 2000USD from jasonmolding.com
If the boss is on the inclined plane or arc plane, the contact area between the bottom of the boss and the inclined plane will be larger, so the risk of shrinkage will be increased. We can reduce the glue around the root of the boss to avoid the appearance problem, which is also known as the crater.
We also have a little reminder, parts of the injection molding can’t connect with the product side together, if you do this, the strength of the boss could be OK, china mold factory but is almost bound to form shrinkage in the side, and angle will be formed in the mould, we can in the post and leave some distance between the sides, and then use rib connected, have to say that strength is taken into account in structure design, rib is god.
Qualified structural design can not only reduce the cost of mold development, but also improve the qualified rate of products and even the overall quality, which means that the cost of our products will follow. If you have any questions on the design, please feel free to contact us.
About JasonMould Industrial Company Limited
Jasonmould is a China mold maker of plastic molds- injection mold, die casting moulds, plastic blow molding, rotational molding, medical plastic injection molding, two shot plastic injection molding, insert molding, overmolding, metal injection molding, micro injection molding, powder injection molding, ceramic injection molding, liquid injection molding, husky injection molding, household mold, casting mold, die mold tool, custom molds, china moulds, rapid prototyping tooling, plastic prototyping tooling, punch press tooling, die and tooling for mobile/ cell phone parts, automotive parts, vacuum cleaners, rechargeable tools, telephones, copiers, computers, multimedia speakers, and many other electronic products and household appliances. And also a plastic product manufacturer, mold manufacturer China– plastic parts, plastic water tank, plastic balls, plastic containers, plastic buckle, plastic anchor, plastic hanger, plastic spoon, plastic pipe fitting, plastic tumble, plastic tableware, plastic cups, plastic bottles, plastic tray, plastic cosmetic container, plastic case, plastic food container, plastic chairs, plastic caps, plastic cap closure, plastic tubes, plastic water pipes, plastic knobs, plastic tubing, plastic utility boxes, plastic racks and so on.
Contact:
Person: James Yuan
Company: JasonMould Industrial Company Limited
Add: LongGang Village,LongXi Town,BoLuo County,HuiZhou City,GuangDong Province, China
Tel: 86-752-6682869
Email: james@jasonmolding.com
Site: https://www.jasonmolding.com/custom-injection-molding/
Do you want to sell vinyl fence gate hinges and buy it from China Manufacturer with lower price
Jiansen Hardware is a supplier of vinyl fence gate hinges and gate latch with drop rod.
we provide two colours for the fence gate hardeare ,white hinges and balck hinges.
Now they are under packing for delivery,we supply the goods mostly to USA market and other europen country.
if you want to get more info ,just email us via mark@hzjiansen.com ,we will reply you within 24 hours.
from today,when we have stock in warehouse ,then you will not have to buy for moq ,if it is out stock,then you have to buy it with moq of 1000sets.
wholesale fence gate hinge
JIANSEN Hardware is a manufacture with more than 10 years hardware mould making experience and supply OEM product. During our development day by day ,we established our hardware producing department separately in 2004.So now we have mould processing and hardware manufacture workshop.
Coupon Code – “freeshipping” on any order 5000 from hzjiansen.com
Our one ¨Cstep team make our exporting service with best price and good quality .For mould ,we have CNC machine ,wire cutting machine ,Grinding machine and milling machine with most steady engineer teams. For products, we have CAD drawing and Pro-E drawing engineers. Our 3D drawings could be suitable for customer¡¯s 3d printing technique.
OUR FACTORY
WORKSHIP
Actually our producing team also with more than 10 year experience. So help our customer to saving cost and getting high efficiency are our pursue.
Trust us ! trust your future.
OUR HONOR
CERTIFICATE
We are professional manufacturer of hardware mould. We has many qualifications certificates
certificate3 certificate2 certificate5 certificate4 certificate1
Company - Hangzhou Jiansen Hardware Co.Ltd
Address - NO.177-1 jincheng road,xindeng town,fuyang district,hangzhou
city,China,311404
Tel - +86-15268828191
E-mail - mark@hzjiansen.com
Site - https://www.hzjiansen.com